A conventional mechanical switch is a yes or no device. Inside, two metal contacts touch when the stem reaches a fixed point, and the keyboard reports a press. Where that point sits is decided at the factory, typically around 2 mm down. Hall effect switches replace the contacts with a magnet and a sensor, which turns the switch into something that reports position continuously. Almost everything interesting about them follows from that one change.
How a Hall effect switch works
The Hall effect is a physical principle: a magnetic field passing through a conductor carrying current produces a small voltage across it, and that voltage changes with the strength of the field. A Hall effect switch puts a small magnet in the moving stem and a Hall sensor on the circuit board beneath it. As you press the key, the magnet gets closer to the sensor, the field gets stronger, and the keyboard can calculate the key's position many times per second.
Because the press is detected by measuring rather than by contact, the keyboard decides in firmware what counts as "pressed". That makes three features possible.
Adjustable actuation
You can set the actuation point per key, from very shallow to near the bottom. A shallow setting makes the key register with a tiny movement, which some gamers like for fast inputs. A deep setting reduces accidental presses for typing. Some keyboards let different keys use different depths, for example shallow WASD for a game and normal depth for everything else.
Very shallow settings have a cost: resting a finger on the key, or a slight bump of the desk, can trigger it. Most people who experiment settle somewhere moderate.
Rapid trigger
On a conventional switch, a key activates at one point on the way down and resets at a slightly higher point on the way up. To press it again you must lift above the reset point. Rapid trigger replaces the fixed points with movement. The key deactivates the moment it starts rising, by a small configurable distance, and activates again the moment it starts falling. You can release and re-press a key while it is still partly down.
In competitive shooters, this is why it became popular. Stopping your character precisely, for example counter-strafing before taking a shot, depends on how quickly the game sees a movement key released. With rapid trigger the release is registered almost as soon as your finger begins to lift, not after it has traveled back up past a reset point. The benefit is real in those games and much smaller elsewhere.
Analog input
Some magnetic keyboards can send key depth as an analog value, like a controller's thumbstick, so pressing harder moves you faster in games that support analog input. Support depends on the keyboard and the game, and it is a niche feature compared with adjustable actuation and rapid trigger.
Durability and feel
With no electrical contacts to wear, Hall effect switches avoid the contact wear that eventually causes key chatter in mechanical switches. The feel depends on the switch: most are linear, and many use housings and springs similar to MX-style linears, so they type like ordinary linears. Magnetic switches are not interchangeable with MX-style switches, even when they look similar, because the board needs the sensor and firmware to read them. Check compatibility before buying replacement switches.
Hall effect vs optical vs mechanical
- Mechanical: metal contact closes at a fixed point. Cheapest, most variety, easy to swap on hot-swap boards.
- Optical: the stem interrupts a light beam at a fixed point. No contact wear; actuation is usually still fixed. See optical vs mechanical switches.
- Hall effect: magnet and sensor measure position continuously. Adjustable actuation and rapid trigger.
What a browser test can and cannot tell you
A web page sees your keyboard only through key down and key up events. It cannot see how far a key is pressed, so no website can verify an actuation depth or a rapid trigger setting. What a browser can do:
- Confirm that every key registers, with the keyboard tester.
- Check how many keys register at once, with the ghosting and rollover test.
- Measure the part of input lag a browser can see (event dispatch delay and the wait for the next frame) with the latency test. The keyboard's own delay happens before the browser receives anything, so no web page can measure it.
- Spot unwanted double presses with the chatter test.
- See whether the board is resolving opposite keys such as A and D (the feature sold as Snap Tap, Snappy Tappy or Rapid Tap), and in which mode, with the SOCD test.
For actuation and rapid trigger, use the keyboard maker's own software, which reads the switch position directly.
Who should buy one
If you play competitive shooters seriously, a Hall effect keyboard with rapid trigger is worth trying. If you mainly type, or play games where keyboard timing is less critical, a well-built conventional board will serve you just as well, often for less money and with far more switch and keycap choice. Our list of best switches for gaming covers conventional options.
Frequently asked questions
What is a Hall effect switch?
A switch with a small magnet in the stem and a magnetic sensor on the circuit board. As the key moves, the sensor measures the changing magnetic field and the keyboard works out how far down the key is. Because there is no contact closing, the actuation point can be set in software, and nothing wears out electrically.
What is rapid trigger?
A feature of analog keyboards where a key deactivates as soon as it starts moving up and reactivates as soon as it starts moving down again, instead of at fixed points. It lets you release and re-press a key without lifting it all the way past a reset point, which helps in games where you tap and release movement keys quickly.
Do I need rapid trigger?
Mainly if you play competitive games that reward very fast stops and direction changes, such as tactical shooters where counter-strafing matters. For typing and most other games, a good conventional keyboard is just as effective. Rapid trigger changes how inputs are timed, not how fast your reflexes are.
Can a website test rapid trigger or actuation depth?
No. A browser only receives key down and key up events. It cannot see how far a key is pressed, so it cannot verify an actuation point or rapid trigger setting. A browser tester can confirm that keys register, measure timing between events, and check rollover and chatter.
Keep learning
- Optical vs mechanical switches.
- Polling rate explained: the other half of input timing.
- What is NKRO?